Terminology - Tips - Maintenance

---

Operating Tips

• Handpiece drive air pressure should not exceed 35 PSI. Increasing air pressure will not increase handpiece performance due to increased back pressure, but may damage the turbine.
• Never tighten any chuck without a bur or bur blank in place or it may cause damage to the chuck.
• Never operate any handpiece without a bur securely in place.
• Do not depress the push button of a handpiece during operation. This may open the chucking mechanism and release the bur.
• Do not use the handpiece to retract the patient’s cheek or other soft tissue. This could generate excessive heat if the end cap is depressed when turbine is running.
• Before operating a handpiece and/or component, always carefully read and follow the manufacturer’s instructions.

Maintenance Procedures

• It is highly recommended that you clean and lubricate the handpiece before and after every autoclave cycle. This ensures longevity of the turbine.
• A toothbrush and hot water or alcohol may be used to clean the outside of a handpiece before sterilization.
• Never wash or immerse the handpiece in cold sterilant or chemical disinfectants containing phenols, acids or chlorines. The chemicals may damage and/or corrode some metals.
• The handpiece turbine should never be removed for cleaning.
• The quick disconnect connections may be cleaned with alcohol and a cotton applicator. Do not use cold sterilants as they may damage “O” rings.
• The fiber optic surfaces may be cleaned using isopropyl alcohol on a cotton applicator.
• Do not pick or probe the fiber optic ends with any sharp instruments.
• Flush or purge the handpiece before removal from the air supply tubing.
• Cleaner/lubricant should be sprayed or dropped ONLY into the drive air hole, which leads to the turbine. The exhaust hole does not connect to the turbine.
• Always run the handpiece with a bur in place for 20 seconds after lubrication.
• Contra angles should be detached and taken apart for lubrication.

Handpiece Terminology

Air Motor – A slow speed handpiece without internal reduction gears or attachments, usually rotating at speeds near 20,000 rpm.
Attachment – A nose cone or angle that quick disconnects on and off the front of a low speed motor to provide various bur holding options.
Auto Chuck – A mechanism enabling the operator to change a bur without the use of a wrench, by pressing a button or raising a lever.
Autoclave – A steam sterilizer which destroys all living organisms through the medium of heat and pressure. Temperatures are raised to 270-275 F while the pressure is raised to 30 psi.
Bur – A rotary dental instrument, which when placed in a handpiece is used to cut or carve tooth structure. Burs come in a variety of shapes and sizes and can be made of high speed steel, carbide, or diamond coated material.
Canister Turbine – A closed cylinder which houses a rotating turbine assembly inside the head of the handpiece. Designed for easy replacement.
Chemiclave – A sterilizer which uses a chemical to generate chamber pressure instead of steam. The absence of water in the process reduces rust and oxidation of instruments.
Chip Air – Air supplied through the handpiece from the dental unit tubing to the cutting surface to cool the tooth or disperse the water spray, while flushing away residual material resulting from the removal of tooth structure.
Chuck – The part in the handpiece turbine used to hold the bur.
Collet – Another word for the chuck mechanism.
Connector – Attaches the handpiece to the dental delivery unit that supplies air and water to the handpiece. There are four types of standard U.S. connectors. They include the 2, or 3-Line (also called a Borden) and 4-Line. The 4-Line (also known as a Midwest) is the most popular connector. In a 4-Line connector, the holes are (1) drive air, (2) chip air, (3) water, and (4) exhaust. Sometimes a fifth line or hole is added for a fiber optic bundle. A newer type of connector, 6 Pin, is now available which provides an electrical connection for a fiber optic light bulb. Hole size and location are indicated by a standardized ISO specification.
Contra Angle – The front section of a handpiece which changes the desired angle to provide better bur access and visibility to the operator during use.
Coolant – Refers to the water spray directed at the bur to cool the tooth when cutting.
Doriot or Universal Angle – Any angle that operates on the front of a nose cone that has a protruding shaft designed to fit into the nose cone chuck.
Drive Air – The compressed air used to rotate the turbine in a dental handpiece.
“E” Type Motor – A motor with a standardized male fitting (connection) that accepts attachments with the matching female connection.
End Cap – The cap, or cover which is removed to install the turbine.
Exhaust – The air discharged from a dental handpiece after spinning the turbine.
Fiber Optic Handpiece – A handpiece through which a transparent fiber or cellular optic bundle transmits light to illuminate the oral cavity.
Friction Grip Chuck – A chuck which holds the bur strictly by friction generated from an internal spring assembly. The bur is simply pushed in and out of the chuck with a special tool using force to overcome friction
Handpiece – A handheld device which engages rotary instruments for cutting, cleaning or polishing the teeth. A handpiece can be belt-driven, pneumatic (air or gas driven) or electric.
High Speed Handpiece – A handpiece which operates at a speed greater than 100,000 RPM.
Jacobs Chuck – A mechanism which utilizes a wrench to tighten the chuck. This design incorporates slots which create jaws that are compressed onto the bur shank when tightened with the corresponding wrench.
Latch Angle – An attachment that holds a specialized bur which is mechanically retained by the use of a swinging hook that engages a recess in the bur shank.
Low Speed Handpiece (or Slowspeed) – A handpiece which operates at speeds ranging from 5,000 to 20,000 rpm.
Lubricant or Oil – A liquid applied to moving parts of a handpiece or attachment in order to reduce friction, heat, or wear, or applied to surfaces in close contact to prevent them adhering to one another. May also include a solvent for cleaning.
Nosecone – A straight attachment used with a slow speed motor which holds a lab type bur (3/32” shank) or any standard doriot attachment.
Prophy Angle – An angle that holds a brush or cup containing prophy paste used by a hygienist for cleaning teeth.
Quick-Disconnect – A handpiece attachment or fitting designed to allow easy separation of the handpiece from the supply tubing.
Replacement Cartridge – Another name for a high speed turbine, usually self contained to allow easy replacement.
Rotary Vane Motor – A type of low speed motor utilizing small vanes instead of a turbine to trap drive air in a rotor assembly to generate rotation.
RPM – Revolutions Per Minute. A unit of measurement indicating speed.
Straight Handpiece – Same as a low or slow speed handpiece. Often refers to a handpiece with a nosecone permanently “fixed” to the motor.
Swivel – Instead of threads at the rear of a handpiece, the swivel is usually a separate part that threads into the supply tubing and incorporates a quick disconnect. Designed to allow the handpiece to rotate where it attaches to the air supply tubing in order to reduce fatigue on the operators wrist.
Turbine – Located in the head of a high speed handpiece, the turbine holds the bur or cutting instrument while rotating from high pressure compressed air. A turbine consists of five components: spindle; chuck; impeller; bearings; and two “O” rings.